Showing posts with label Sunlight. Show all posts
Showing posts with label Sunlight. Show all posts

Sunday, April 15, 2012

Anti-Reflective and Ultraviolet Coatings

What is Anti-Reflective and Ultraviolet Coatings?

A common problem with sunglasses is called back-glare. This is light that hits the back of the lenses and bounces into the eyes. The purpose of an anti-reflective (AR) coating is to reduce these reflections off the lenses.


Similar to a scratch-resistant coating, AR is made of a very hard, thin film that is layered on the lens. It is made of material that has an index of refraction that is somewhere between air and glass. This causes the intensity of the light reflected from the inner surface and the light reflected from the outer surface of the film to be nearly equal. When applied in a thickness of about a quarter of light's wavelength, the two reflections from each side of the film basically cancel each other out through destructive interference, minimizing the glare you see. AR coatings are also applied to the front of prescription eyewear and some sunglasses to eliminate the "hot spot" glare that reflects off the lens.

Ultraviolet Coating

Several of the most serious eye problems can be linked to one cause: UV light. UV is often separated into two categories based on the frequency and wavelength of the light: UV-A and UV-B.


As a natural protection mechanism, the cornea of your eye absorbs all of the UV-B and most of the UV-A light. But some of the UV-A light reaches the lens of the eye, and over time this absorption can lead to cataracts. The small amount of UV-A that gets past your cornea and reaches the retina can eventually lead to macular degeneration, the leading cause of blindness in people older than age 65. Intense and prolonged exposure to UV radiation can cause either cancer of the eye or photokeratitis, which is basically a sunburn on your retina. Because it occurs most often when a person is outside on bright winter day, with sunlight glaring off the snow, this condition is commonly known as snow blindness.

A good UV coating on your sunglasses can eliminate UV radiation, and you should check to make sure that your sunglasses filter out 100 percent of both types of UV rays. There should be a statement on the label telling you how much UV protection the sunglasses have. You want 100-percent protection.

Reflective and Scratch-resistant Coatings

What is the purpose of Mirroring and Scratch-resistant Coatings?

Reflective sunglasses often have a mirrored look. The lenses in these sunglasses have a reflective coating applied in a very thin, sparse layer - so thin that it's called a half-silvered surface.

The name "half-silvered" comes from the fact that the reflective molecules coat the glass so sparsely that only about half the molecules needed to make the glass an opaque mirror are applied. At the molecular level, there are reflective molecules speckled all over the glass in an even film but only half of the glass is covered. The half-silvered surface will reflect about half the light that strikes its surface, while letting the other half go straight through.


Often, the mirror coating is applied as a gradient that gradually changes shades from top to bottom. This provides additional protection from light coming from above while allowing more light to come in from below or straight ahead. What that means is that if you are driving, the sun's rays are blocked but you can see the dashboard. Sometimes the coating is bi-gradient, shading from mirrored at top and bottom to clear in the middle.

The key problem with reflective sunglasses is that the coating is easily scratched. Apparently, sunglass manufacturers have not been able to successfully apply a scratch-resistant layer on top of the reflective coating. Therefore, the scratch-resistant coating is applied first to protect the lenses and the reflective coating is applied over it.

Scratch-resistant Coating


While glass is naturally scratch resistant, most plastics are not. To compensate, manufacturers have developed a variety of ways to apply optically clear hard films to the lens. Films are made of materials such as diamond-like carbon (DLC) and polycrystalline diamond. Through a process of ionization, a thin but extremely durable film is created on the surface of the lens. 

Saturday, April 14, 2012

What is Photochromic Technology?

What is Photochromic Technology?

Sunglasses or prescription eyeglasses that darken when exposed to the sun are called photochromic, or sometimes photochromatic. Developed by Corning in the late 1960s and popularized by Transitions in the 1990s, photochromic lenses rely on a specific chemical reaction to UV radiation.

Photochromic lenses have millions of molecules of substances, such as silver chloride or silver halide, embedded in them. The molecules are transparent to visible light in the absence of UV light, which is the normal makeup of artificial lighting. But when exposed to UV rays in sunlight, the molecules undergo a chemical process that causes them to change shape. The new molecular structure absorbs portions of the visible light, causing the lenses to darken. The number of the molecules that change shape varies with the intensity of the UV rays.

When you go indoors and out of the UV light, the reverse chemical reaction takes place. The sudden absence of UV radiation causes the molecules to "snap back" to their original shape, resulting in the loss of their light absorbing properties. In either direction, the entire process occurs very rapidly.


In the PhotoBrown and PhotoGrey products made by Corning in the '60s, the lenses were made of glass, and the molecules are distributed evenly throughout each entire lens. The problem with this method became apparent when it was applied to prescription glasses, in which different parts of the lens can vary in thickness. The thicker parts would appear darker than the thinner areas.

With the increasing popularity of plastic lenses, a new method has been developed. By immersing plastic lenses in a chemical bath, the photochromic molecules are actually absorbed to a depth of about 150 microns into the plastic. This proved to be much better than a simple coating, which would only be about 5 microns thick and would not provide enough molecules to make the lenses sufficiently dark. This plastic lens absorption process has been popularized by Transitions, the leading manufacturer of photochromic lenses.

What is Polarization?

What is Polarization?

Light waves from the sun, or even from an artificial light source such as a light bulb, vibrate and radiate outward in all directions. Whether the light is transmitted, reflected, scattered or refracted, when its vibrations are aligned into one or more planes of direction, the light is said to be polarized. Polarization can occur either naturally or artificially. You can see an example of natural polarization every time you look at a lake. The reflected glare off the surface is the light that does not make it through the "filter" of the water, and is the reason why you often cannot see anything below the surface, even when the water is very clear.


A polarized filter passes only the light that does not match its orientation. Only the part of the light wave that is not aligned with the slots in the filter can pass through. Everything else is absorbed. The light coming through the filter is considered polarized. Polarized filters are most commonly made of a chemical film applied to a transparent plastic or glass surface. The chemical compound used will typically be composed of molecules that naturally align in parallel relation to one another. When applied uniformly to the lens, the molecules create a microscopic filter that absorbs any light matching their alignment.

Most of the glare that causes you to wear sunglasses comes from horizontal surfaces, such as water or a highway. When light strikes a surface, the reflected waves are polarized to match the angle of that surface. So, a highly reflective horizontal surface, such as a lake, will produce a lot of horizontally polarized light. Therefore, the polarized lenses in sunglasses are fixed at an angle that only allows vertically polarized light to enter. You can see this for yourself by putting on a pair of polarized sunglasses and looking at a horizontal reflective surface, like the hood of a car. Slowly tilt your head to the right or left. You will notice that the glare off the surface brightens as you adjust the angle of your view.


A lot of sunglasses advertised as polarizing actually are not. There's a simple test you can perform before you buy them to make sure. Find a reflective surface, and hold the glasses so that you are viewing the surface through one of the lenses. Now slowly rotate the glasses to a 90-degree angle, and see if the reflective glare diminishes or increases. If the sunglasses are polarized, you will see a significant diminishing of the glare.

Why Sunglasses are Important for Eyes?

Why Sunglasses are Important for Eyes?

A pair of sunglasses seems so simple -- it's two pieces of tinted glass or plastic in some sort of plastic or metal frame. How much more straightforward can something get? It turns out that there are many different things you can do with two pieces of glass, and these things can have a big effect on you when you use the lenses.

Four things that sunglasses should do for you:
  1. Sunglasses provide protection from ultraviolet rays in sunlight. Ultraviolet (UV) light damages the cornea and the retina. Good sunglasses can eliminate UV rays completely.
  2. Sunglasses provide protection from intense light. When the eye receives too much light, it naturally closes the iris. Once it has closed the iris as far as it can, the next step is squinting. If there is still too much light, as there can be when sunlight is reflecting off of snow, the result is damage to the retina. Good sunglasses can block light entering the eyes by as much as 97 percent to avoid damage.
  3. Sunglasses provide protection from glare. Certain surfaces, such as water, can reflect a great deal of light, and the bright spots can be distracting or can hide objects. Good sunglasses can completely eliminate this kind of glare using polarization.
  4. Sunglasses eliminate specific frequencies of light. Certain frequencies of light can blur vision, and others can enhance contrast. Choosing the right color for your sunglasses lets them work better in specific situations.

When you buy a pair of cheap sunglasses, you often give up all of these benefits and can even make things worse. For example, if your sunglasses offer no UV protection, you increase your exposure to UV rays. The cheap sunglasses block some of the light, causing your iris to open to allow more light in. This lets in more of the UV light as well, increasing the damage UV light can cause to the retina. So there is a difference. Buying the right pair of good sunglasses for the conditions in which you use them gives you maximum protection and performance.

Related Reading: Technologies used by Sunglasses

Technologies used by Sunglasses

What are the Technologies used by Sunglasses?

Sunglasses use a variety of technologies to eliminate the problems with light that were discussed in a previous post. The different technologies currently in use are:
  1. Tinting
  2. Polarization
  3. Photo-chromatic lenses
  4. Mirroring
  5. Scratch-resistant coating
  6. Anti-reflective coating
  7. UV coating

Tinting The color of the tint determines the parts of the light spectrum that are absorbed by the lenses. Manufacturers use different colors to produce specific results.
  1. Gray tints are great all-purpose tints that reduce the overall amount of brightness with the least amount of color distortion. Gray lenses offer good protection against glare, making them a good choice for driving and general use.
  2. Yellow or gold tints reduce the amount of blue light while allowing a larger percentage of other frequencies through. Since blue light tends to bounce and scatter off a lot of things, it can create a kind of glare known as blue haze. The yellow tint virtually eliminates the blue part of the spectrum and has the effect of making everything bright and sharp. That's why snow glasses are usually yellow. This tint really distorts color perception, which makes it inappropriate for any activity that relies on accurate color.
  3. Amber and brownish tints are also good general purpose tints. They have the added benefit of reducing glare and have molecules that absorb higher frequency colors, such as blue, in addition to UV rays. There has been research that suggests that near-UV light frequencies such as blue and violet can contribute to the formation of cataracts over time. In fact, Sun Tiger has a patent on a particular version of these called Blue Blockers. These sunglasses also distort colors similar to yellow lenses, but increase contrast and clarity.
  4. Green tints on lenses filter some blue light and reduce glare. Because green tints offer the highest contrast and greatest visual acuity of any tint, they are very popular.
  5. Purple and rose tints offer the best contrast of objects against a green or blue background. They make a good choice for hunting or water skiing.
Many manufacturers employ a process called constant density to tint the lenses. It is the oldest method of creating sunglasses and involves a glass or polycarbonate mixture with a uniform color throughout the material. The tint is built right into the lenses when they are created. Tinting can also be accomplished by applying a coat of light-absorbing molecules to the surface of clear polycarbonate. The most common method for tinting polycarbonate lenses is to immerse the lenses in a special liquid containing the tinting material. The tint is slowly absorbed into the plastic. To make a darker tint, the lenses are simply left in the liquid longer.

Monday, April 9, 2012

Innovative use of Sun's Energy

How Sunlight & Heat simultaneously can be converted to Electricity?

A new type of device that uses both heat and light from the sun should be more efficient than conventional solar cells, which convert only the light into electricity.


The device relies on a physical principle discovered and demonstrated by researchers at Stanford University. In their prototype, the energy in sunlight excites electrons in an electrode, and heat from the sun coaxes the excited electrons to jump across a vacuum into another electrode, generating an electrical current. The device could be designed to send waste heat to a steam engine and convert 50 percent of the energy in sunlight into electricity--a huge improvement over conventional solar cells.

The most common silicon solar cells convert about 15 percent of the energy in sunlight into electricity. More than half of the incoming solar energy is lost as heat. That's because the active materials in solar cells can interact with only a particular band of the solar spectrum; photons below a certain energy level simply heat up the cell.

One way to overcome this is to stack active materials on top of one another in a multijunction cell that can use a broader spectrum of light, turning more of it into electrical current instead of heat, for efficiencies up to about 40 percent. But such cells are complex and expensive to make.

Looking for a better way to take advantage of the sun's heat, a highly efficient cogeneration system that uses the expansion of burning gas to drive a turbine and the heat from the combustion to power a steam engine. But thermal energy converters don't pair well with conventional solar devices. The hotter it is, the more efficient thermal energy conversion becomes. Solar cells, by contrast, get less efficient as they heat up. At about 100 °C, a silicon cell won't work well; above 200 °C, it won't work at all.

The breakthrough came when the Stanford researchers realized that the light in solar radiation could enhance energy conversion in a different type of device, called a thermionic energy converter, that's conventionally driven solely by heat. Thermionic converters consist of two electrodes separated by a small space. When the positive electrode, or cathode, is heated, electrons in the cathode get excited and jump across to the negative electrode, or anode, driving a current through an external circuit. The cathode in these devices is typically made of metals such as cesium.

The researchers are testing devices made from materials that are better suited to solar energy conversion, including silicon and gallium arsenide. They're also developing ways of treating these materials so that the device will work more efficiently in a temperature range of 400 °C to 600 °C; solar concentrators would be used to generate such high temperatures from sunlight.

Even at high temperatures, the photon-enhanced thermionic converter will generate more heat than it can use; this heat could be coupled to a steam engine for a solar-energy-to-electricity conversion efficiency exceeding 50 percent. These systems are likely to be too complex and expensive for small-scale rooftop installations. But they could be economical for large solar-farm installations.